ATV32HU22N4

ATV32

3 phase

323...550 V

47.5...63 Hz

3 hp 380...480 V

5.7 kVA 500 V 3 phase 2.2 kW / 3 hp

5.5 A 4 kHz 500 V 2.2 kW / 3 hp

0.0005...0.599 kHz

2...16 kHz adjustable

+/- 10 % of nominal slip 0.2 Tn to Tn

170...200 %

Voltage/frequency ratio - Energy Saving, quadratic U/fFlux vector control without sensor, standardVoltage/frequency ratio, 5 pointsFlux vector control without sensor - Energy Saving, NoLoad lawVoltage/frequency ratio, 2 points

Adjustable PID regulator

1 LED red drive voltage1 LED green CANopen run1 LED red CANopen error1 LED red drive fault

43 dB 86/188/EEC

Screw terminal 0.5...1.5 mm², AWG 18...AWG 14 control)Removable screw terminals 1.5...2.5 mm², AWG 14...AWG 12 motor/braking resistor)Screw terminal 1.5...4 mm², AWG 14...AWG 10 power supply)

Internal supply for reference potentiometer (1 to 10 kOhm) 10.5 V DC +/- 5 %, <10 mA overload and short-circuit protection

AI1 voltage 0...10 V DC 30000 Ohm 10 bitsAI2 bipolar differential voltage +/- 10 V DC 30000 Ohm 10 bitsAI3 current 0...20 mA (or 4-20 mA, x-20 mA, 20-x mA or other patterns by configuration) 250 Ohm 10 bits

LI1...LI6 8 ms +/- 0.7 ms logicR1A, R1B, R1C 2 ms relayR2A, R2C 2 ms relay

+/- 0.2...0.5 % of maximum value AI1, AI2, AI3)+/- 0.3 % AO1)

AO1 software-configurable current 0...20 mA 800 Ohm 10 bitsAO1 software-configurable voltage 0...10 V 470 Ohm 10 bits

Configurable relay logic R1A, R1B, R1C) NO/NC - 100000 cyclesConfigurable relay logic R2A, R2B) NO - 100000 cyclesLogic LO)

R1 3 A 250 V AC resistive, cos phi = 1R1 4 A 30 V DC resistive, cos phi = 1R1, R2 2 A 250 V AC inductive, cos phi = 0.4R1, R2 2 A 30 V DC inductive, cos phi = 0.4R2 5 A 250 V AC resistive, cos phi = 1R2 5 A 30 V DC resistive, cos phi = 1

Programmable (sink/source) LI1...LI4)24...30 V DC level 1 PLCProgrammable as pulse input 20 kpps LI5)24...30 V DC level 1 PLCSwitch-configurable PTC probe LI6)24...30 V DCSafe torque off STO)24...30 V DC - 1500 Ohm

SCUSLinearDeceleration ramp adaptationRamp switchingDeceleration ramp automatic stop DC injectionU

Input phase breaks driveOvercurrent between output phases and earth driveOverheating protection driveShort-circuit between motor phases driveThermal protection drive

1 RJ45 on front face)Modbus/CANopen

RTU Modbus

1...127 CANopen1...247 Modbus

1.2/50 µs - 8/20 µs surge immunity test, level 3 IEC 61000-4-5Conducted radio-frequency immunity test, level 3 IEC 61000-4-6Electrical fast transient/burst immunity test, level 4 IEC 61000-4-4Electrostatic discharge immunity test, level 3 IEC 61000-4-2Radiated radio-frequency electromagnetic field immunity test, level 3 IEC 61000-4-3Voltage dips and interruptions immunity test IEC 61000-4-11

12.8 in (325 mm)

6.6 lb(US) (3 kg)

Mid

EN 55011 class A group 1EN/IEC 61800-3EN 61800-3 environments 1 category C2EN/IEC 61800-5-1EN 61800-3 environments 2 category C2

CE

IP20 EN/IEC 61800-5-1

15 gn 11 msEN/IEC 60068-2-27

14...122 °F (-10...50 °C) without derating122...140 °F (50...60 °C) with derating factor