ATV71LD45N4Z

60 hp, 3 phase 380...480 V

Altivar Lift

Lift

CANopenModbus

Integrated

22 kA 3 phase

155 A2 s 3 phase / 45 kW / 60 hp

1...100 asynchronous motor in open-loop mode, without speed feedback1...50 synchronous motor in open-loop mode, without speed feedback1...1000 asynchronous motor in closed-loop mode with encoder feedback

170 %, +/- 10 % 60 s220 %, +/- 10 % 2 s

for drive voltage 1 LED (red)

Electrical between power and control

Terminal 2.5 mm², AWG 14 AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR)Terminal 50 mm², AWG 1/0 L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB)

Internal supply for reference potentiometer (1 to 10 kOhm) 10.5 V DC +/- 5 %, <10 A overload and short-circuit protectionInternal supply 24 V DC 21...27 V), <200 A overload and short-circuit protection

R1A, R1B, R1C 7 ms +/- 0.5 ms discreteR2A, R2B 7 ms +/- 0.5 ms discreteAO1 2 ms +/- 0.5 ms analog <= 100 ms in STO (Safe Torque Off)

+/- 0.15 % of maximum value AI1-/Al1+, AI2)+/- 0.2 % AO1)

Configurable relay logic R1A, R1B, R1C) NO/NC - 100000 cyclesConfigurable relay logic R2A, R2B) NO - 100000 cycles

5 A 250 V AC resistive cos phi = 1 L/R = 0 ms R1, R2)5 A 30 V DC resistive cos phi = 1 L/R = 0 ms R1, R2)2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms R1, R2)2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms R1, R2)

Positive logic LI6)if configured as logic input, < 5 V, > 11 VNegative logic LI6)if configured as logic input, > 16 V, < 10 VPositive logic LI1...LI5), < 5 V, > 11 VNegative logic LI1...LI5), > 16 V, < 10 VPositive logic PWR), < 2 V, > 17 V

> 1 mOhm 500 V DC for 1 minute to earth

1 RJ45 on front face)Modbus1 RJ45 on terminal)ModbusMale SUB-D 9 on RJ45CANopen

RTU Modbus

8 bits, 1 stop, even parity Modbus on front face8 bits, odd even or no configurable parity Modbus on terminal

1...247 Modbus1...127 CANopen

7

2

1

Flux vector control with sensor, standardVoltage/frequency ratio - Energy Saving, quadratic U/fVoltage/frequency ratio, 2 pointsVoltage/frequency ratio, 5 pointsFlux vector control without sensor, standardFlux vector control without sensor, ENA (energy Adaptation) systemFlux vector control without sensor, 2 points

S, U or customizedAutomatic adaptation of ramp if braking capacity exceeded, by using resistorLinear adjustable separately from 0.01 to 9000 s

1...16 kHz adjustable

13.3 Ohm

Overheating protection driveThermal protection driveShort-circuit between motor phases driveInput phase breaks driveOvercurrent between output phases and earth driveOvervoltages on the DC bus driveBreak on the control circuit driveAgainst exceeding limit speed driveLine supply undervoltage driveLine supply overvoltage driveAgainst input phase loss driveThermal protection motorMotor phase break motorPower removal motor

IP20 on upper part without blanking plate on cover EN/IEC 61800-5-1IP20 on upper part without blanking plate on cover EN/IEC 60529IP21 EN/IEC 61800-5-1IP21 EN/IEC 60529IP41 on upper part EN/IEC 61800-5-1IP41 on upper part EN/IEC 60529IP54 on lower part EN/IEC 61800-5-1IP54 on lower part EN/IEC 60529

15 gn 11 ms EN/IEC 60068-2-27

5...95 % without condensation IEC 60068-2-35...95 % without dripping water IEC 60068-2-3

<= 3280.84 ft (1000 m) without derating3280.84...9842.52 ft (1000...3000 m) with current derating 1 % per 100 m

C-tickCSANOM 117UL

EN 61800-3 environments 1 category C3EN/IEC 61800-3EN 55011 class A group 2UL Type 1IEC 60721-3-3 class 3S2EN/IEC 61800-5-1IEC 60721-3-3 class 3C1EN 61800-3 environments 2 category C3

Electrostatic discharge immunity test level 3 IEC 61000-4-2Radiated radio-frequency electromagnetic field immunity test level 3 IEC 61000-4-3Electrical fast transient/burst immunity test level 4 IEC 61000-4-41.2/50 µs - 8/20 µs surge immunity test level 3 IEC 61000-4-5Conducted radio-frequency immunity test level 3 IEC 61000-4-6Voltage dips and interruptions immunity test IEC 61000-4-11