ATV650D37N4EU

Integrated 164.04 ft (50 m) IEC 61800-3 category C2Integrated 492.1 ft (150 m) IEC 61800-3 category C3

380...480 V - 15...10 %

Forced convection

30 kW heavy duty)37 kW normal duty)

57.3 A 480 V normal duty)54.8 A 380 V heavy duty)48.3 A 480 V heavy duty)66.2 A 380 V normal duty)

40.2 kVA 480 V heavy duty)47.6 kVA 480 V normal duty)

Optimized torque modeVariable torque standardOptimized torque mode

0.1...500 Hz

4...12 kHz with derating factor2...12 kHz adjustable

Positive logic (source) DI1...DI8), < 5 V, > 11 VNegative logic (sink) DI1...DI8), > 16 V, < 10 V

Slot A communication module, PROFINETSlot A communication module, DeviceNetSlot A communication module, Modbus TCP/EtherNet/IPSlot A communication module, CANopen daisy chain RJ45Slot A communication module, CANopen SUB-D 9Slot A communication module, CANopen screw terminalsSlot A/slot B digital and analog I/O extension moduleSlot A/slot B output relay extension moduleSlot A communication module, Ethernet IP/Modbus TCP/MD-Link communication module, BACnet MS/TP communication module, Ethernet PowerlinkSlot A communication module, Profibus DP V1

92.3 A 60 s heavy duty)82 A 60 s normal duty)

0

<= power supply voltage

Not available in permanent magnet motor lawAdjustableCan be suppressedNot available in permanent magnet motor law

Ethernet2-wire RS 485

Safe torque off motorMotor phase break motorThermal protection driveSafe torque off driveOverheating driveOvercurrent between output phases and earth driveOverload of output voltage driveShort-circuit protection driveMotor phase break driveOvervoltages on the DC bus driveLine supply overvoltage driveLine supply undervoltage driveLine supply phase loss driveOverspeed driveBreak on the control circuit driveThermal protection motor

Analog input 0.012/50 HzDisplay unit 0.1 Hz

Line side screw terminal 25...50 mm²Motor screw terminal 35...50 mm²Control removable screw terminals 0.5...1.5 mm²

8 bits, configurable odd, even or no parity

Half duplex, full duplex, autonegotiation Ethernet/Modbus TCP

Slave Modbus TCP

for embedded communication status 3 LEDs (dual colour) for communication module status 4 LEDs (dual colour) for presence of voltage 1 LED (red) for local diagnostic 3 LEDs

35.8 in (910 mm)

110.2 lb(US) (50 kg)

AI1, AI2, AI3 software-configurable voltage 0...10 V DC 31.5 kOhm 12 bitsAI1, AI2, AI3 software-configurable current 0...20 mA 250 Ohm 12 bitsAI2 voltage analog input - 10...10 V DC 31.5 kOhm 12 bits

DI7, DI8 programmable as pulse input 0...30 kHz, 24 V DC <= 30 V)

2

5 ms +/- 1 ms DI5, DI6) - discrete input5 ms +/- 0.1 ms AI1, AI2, AI3) - analog input10 ms +/- 1 ms AO1) - analog output2 ms +/- 0.5 ms DI1...DI4) - discrete input

AO1, AO2 +/- 0.2 % analog outputAI1, AI2, AI3 +/- 0.15 % of maximum value analog input

Configurable relay logic R2 sequence relay NO 100000 cyclesConfigurable relay logic R3 sequence relay NO 100000 cyclesConfigurable relay logic R1 fault relay NO/NC 100000 cycles

Relay output R1, R2, R3 5 mA 24 V DC

Between power and control terminals

66.2 A

Wall mounted

69.7 dB

<48 % from 80...100 % of load IEC 61000-3-12

3

15 gn 11 ms IEC 60068-2-27

104...122 °F (40...50 °C) with derating factor)5...104 °F (-15...40 °C) without derating)

1000...4800 m with current derating 1 % per 100 m<= 3280.84 ft (1000 m) without derating

CE