ATV61HD75N4

380...480 V - 15...10 %

137 A 480 V 3 phase 75 kW / 100 hp167 A 380 V 3 phase 75 kW / 100 hp

With heat sink

22 kA 3 phase

12 kHz

Voltage/frequency ratio - Energy Saving, quadratic U/fVoltage/frequency ratio, 5 pointsFlux vector control without sensor, standardVoltage/frequency ratio, 2 points

CANopenModbus

Communication card APOGEE FLNCommunication card BACnetCommunication card CC-LinkController inside programmable cardCommunication card DeviceNetCommunication card EtherNet/IPCommunication card FipioI/O extension cardCommunication card Interbus-SCommunication card LonWorksCommunication card METASYS N2Communication card Modbus PlusCommunication card Modbus TCPCommunication card Modbus/Uni-TelwayMulti-pump cardCommunication card Profibus DPCommunication card Profibus DP V1

323...528 V

47.5...63 Hz

0.1...500 Hz

+/- 10 % of nominal slip 0.2 Tn to Tn without speed feedback

130 % of nominal motor torque +/- 10 % 60 s

Frequency PI regulator

for drive voltage 1 LED (red)

Between power and control terminals

Terminal 2.5 mm² / AWG 14 AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR)Terminal 150 mm² / 300 kcmil L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB)

Internal supply for reference potentiometer (1 to 10 kOhm) 10.5 V DC, +/- 5 %, <10 mA overload and short-circuit protectionInternal supply 24 V DC 21...27 V), <200 mA overload and short-circuit protectionExternal supply 24 V DC 19...30 V)

AI1-/Al1+ bipolar differential voltage +/- 10 V DC 24 V max 11 bits + signAI2 software-configurable current 0...20 mA 242 Ohm 11 bitsAI2 software-configurable voltage 0...10 V DC 24 V max 30000 Ohm 11 bits

+/- 0.6 % AI1-/Al1+) for a temperature variation 60 °C+/- 0.6 % AI2) for a temperature variation 60 °C+/- 1 % AO1) for a temperature variation 60 °C

1

2

<= 100 ms in STO (Safe Torque Off)R1A, R1B, R1C <= 7 ms +/- 0.5 msR2A, R2B <= 7 ms +/- 0.5 ms

R1, R2 2 A 250 V AC inductive, cos phi = 0.4 7 msR1, R2 2 A 30 V DC inductive, cos phi = 0.4 7 msR1, R2 5 A 250 V AC resistive, cos phi = 1 0 msR1, R2 5 A 30 V DC resistive, cos phi = 1 0 ms

Programmable LI1...LI5) 24 V DC <= 30 V)level 1 PLC - 3500 OhmSwitch-configurable LI6) 24 V DC <= 30 V)level 1 PLC - 3500 OhmSwitch-configurable PTC probe LI6)0...6 - 1500 OhmSafety input PWR) 24 V DC <= 30 V) - 1500 Ohm

Linear adjustable separately from 0.01 to 9000 sS, U or customizedAutomatic adaptation of ramp if braking capacity exceeded, by using resistor

Against exceeding limit speed driveAgainst input phase loss driveBreak on the control circuit driveInput phase breaks driveLine supply overvoltage driveLine supply undervoltage driveOvercurrent between output phases and earth driveOverheating protection driveOvervoltages on the DC bus drivePower removal driveShort-circuit between motor phases driveThermal protection driveMotor phase break motorPower removal motorThermal protection motor

Analog input 0.024/50 HzDisplay unit 0.1 Hz

2-wire RS 485 Modbus

4800 bps, 9600 bps, 19200 bps, 38.4 Kbps Modbus on terminal9600 bps, 19200 bps Modbus on front face20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps CANopen

1...127 CANopen1...247 Modbus

CE

97.003 lb(US) (44 kg)

24.8 in (630 mm)

63.7 dB 86/188/EEC

Conducted radio-frequency immunity test level 3 IEC 61000-4-6Electrical fast transient/burst immunity test level 4 IEC 61000-4-4Electrostatic discharge immunity test level 3 IEC 61000-4-2Radiated radio-frequency electromagnetic field immunity test level 3 IEC 61000-4-3Voltage dips and interruptions immunity test IEC 61000-4-11

GOSTCSAC-tickNOM 117ULDNV

IP20 on upper part without blanking plate on cover IEC 60529IP20 on upper part without blanking plate on cover IEC 61800-5-1IP21 IEC 60529IP21 IEC 61800-5-1IP41 on upper part IEC 60529IP41 on upper part IEC 61800-5-1IP54 on lower part IEC 60529IP54 on lower part IEC 61800-5-1

15 gn 11 ms IEC 60068-2-27

14...122 °F (-10...50 °C) without derating)122...140 °F (50...60 °C) with derating factor)